THOMPSON SUBMACHINE GUN DRAWINGS

        Each of the following consists of a set of two full size 24” x 40” reprints of original U.S. Army drawings:

 

 M1928A1 OUTSIDE AND SECTION VIEWS;  Complete gun outside top and side views and  longitudinal section view showing all parts  and part numbers. 

 

 M1 OUTSIDE AND SECTION VIEWS:  Same as 1. except of M1 gun. 

 

 M1A1 OUTSIDE AND SECTION VIEWS:  Same as 1. except of M1A1 gun. 

 

 M1928A1 RECEIVER AND TRIGGER HOUSING (FRAME) MANUFACTURING DRAWINGS:

 Includes all dimensions, material, heat treatment, hardness, and finish specifications necessary to manufacture the receiver and    trigger housing. 

 

M1/M1A1 RECEIVER AND TRIGGER HOUSING (FRAME) MANUFACTURING DRAWINGS:  Same as 4. except of M1/M1A1 gun.        

 

MAGAZINES OUTSIDE AND SECTION VIEWS:  Complete 50 round drum and clip magazines outside views and section views showing all parts and part numbers.   Also includes 24” x 36” 1921 Auto-Ordnance assembly drawing of the Type “C” 100 cartridge drum.  Three drawing sets.

 

 

THOMPSON  MANUFACTURING  DRAWINGS

 

As the supply of original Thompson parts diminishes and the prices go higher and higher for those that remain, the temptation to manufacture new ones increases.  I have no problem with that as long as the newly made parts are as good or better than the originals.  It seems, though, that everyone who makes parts claims their parts are “made to the original specifications/drawings”.  When I have made inquiries to the makers as to where they got the “original specifications/drawings” (I’m always searching for original Thompson engineering data.), I am invariably told that the “original specifications/drawings” were derived from studying an original part.  You can’t have it both ways.  Either you have the “original specifications/drawings” or you don’t.  Copying an existing part is not manufacturing to the “original specifications/drawings”.  There is no way of knowing what the original design dimensions were or what limits were placed on manufacturing deviations (tolerances) by the engineers to assure that the parts are interchangeable within every gun.  Manufacturing is an imprecise activity at best.  Parts are never exactly in accordance with the original design dimensions.  Therefore, copying an existing part, which already deviates from the original design dimensions, adds more manufacturing deviations, producing a part that may not fit in every gun.

 

Part of the solution to the problem of bad parts is to at least start with the original specifications/drawings.  As many of you know, I have most every original specification/drawing for the Thompson guns as well as the tools, accessories, ammunition, etc.  However, there are hundreds of them in various size formats and in varying conditions.  And they are packed away in storage.  Even though I have tried to help wanabe manufacturers in the past at no charge, the time involved is excessive, particularly when no great benefit to the Thompson world comes of it. 

 

I have, therefore, decided to digitize and restore all the drawings and make them available to everyone.  The only exceptions will be those full size drawings that I already offer in my catalog and drawings of parts that I either manufacture or intend to manufacture.  “A” size (8-1/2” x 11”) and “B” size (11” x 17”) drawings will be provided in their original sizes.  Larger drawings will be reduced to “b” size.  The price is $20 per single drawing sheet postpaid.  

 

Bear in mind that every part has its own drawing and if it is a part of a permanent assembly, there will be an assembly drawing.  For example, there is no one drawing showing the manufacturing information for the pivot plate.  There is an assembly drawing which shows all the parts in position and instructions as to how the parts are assembled.  Then there is a drawing for the plate, another for the trigger axis and another for the sear axis.  Material and heat treatment specifications for each part are on yet another drawing.  However, rather than requiring two drawings for every part, I will add the material and heat treatment specifications information to the drawing at no additional charge. 

 

You need to identify the exact drawing you want by number and name.  If you do not know the number or are unsure as to the true part name, provide a COMPLETE description of the part and the model of the gun it goes on.  I offer full size gun assembly drawings in my catalog that number and name every part in the gun, which should help.  If you have any questions regarding interpreting the drawing after you receive it, I will try to help you. 

 

A great deal of time and money has been expended to digitize and restore the drawings, which is copyrighted, not to mention the extraordinary effort to locate the drawings.  So, please respect the copyright limitations.  The drawings are for the purchaser’s use only.  They are not to be copied for further distribution.

                                                                                       

Because of the nature of this product there will be no refunds unless I make a mistake.  

E-M: ThompsonSMG@Mail.com 

 

 

UPDATE: There has been a problem with the larger Thompson drawings being illegible when reduced to 8-1/2" x 11".  Therefore, the larger drawings will now be reduced to 11" x 17" although this is more difficult for me and creates a delay. 

 

UPDATE:  I have discontinued offering any drawings other than the full size Receiver/Frame manufacturing, Gun Assembly and Magazines Assembly drawings as described above.  It just became too time consuming.